Fiber Optic Mode Converter/Repeater

Applications

Because of its multiplexing capability, the TC3007 is often used to increase existing fiber optic cable capacity in LAN or Telephony environments that require connecting different fiber types or wavelengths, regenerating optical signals and/or extending transmission distances. Typical environments include PABX, Ethernet, Fast Ethernet, Token Ring, FDDI, ATM and SONET (OC1 & OC3).

Top

Description

The TC3007 Multimode-to-Single Mode Fiber Optic Converter converts multimode formats to single mode formats, or vice versa, for data transmission up to 200 Mbps. Transmission distances to more than 50 km are possible with the Laser 1550nm option (34dB loss budget).

The TC3007 functions both as a Fiber Optic Mode Converter/Repeater and a 2-Channel Wave Division Multiplexer. This benefits users by effectively doubling existing fiber cable capacity in addition to its mode conversion/repeater functions.

The TC3007 will convert or repeat all popular wavelengths including 850nm, 1300nm or 1550nm. It is compatible with most communication technologies including Ethernet, Fast Ethernet, Token Ring, TAXI, OC1/OC3, ATM, FDDI and SONET. It is completely transparent to incoming data and protocols.

The TC3007 provides users with several key features including Local/Remote Loopback, Test Signal Generator, Dry Contact Alarm, Audible Alarm Buzzer, Power Redundancy, and Standalone or Rack Mount modularity.

The Test Signal Generator and Dry Contact Alarm are particularly beneficial. The Signal Generator (160Mbps) helps technicians conduct various installation tests including fiber link verifications. The Dry Contact Alarm, which includes an audible alarm buzzer, identifies Optical Signal Loss on either the multimode or single mode ends.

Power redundancy is load sharing and switches over automatically in the event of a failure. Power can be either 12VDC, 24VDC, -48VDC, 115/230VAC. Standalone versions are modular, i.e. used either in a standalone case or in a rack mount assembly. Standard connectors are ST or FC type. An extreme temperature version (-20° to 70°C), Model TC3007T, is also available.

A terminal block connector on the rear panel provides for the dry contact relay alarm. Normally in the OPEN position, any loss of electrical or optical signal will trigger an alarm condition and force the switch to the CLOSED position. This relay can be used in conjunction with an external device to monitor the condition of the link.

Top

Technical Specifications

Data Rates
Up to 200 Mbps
Optical - Single Fiber Side
Transmitter	LASER, HI-POWER LASER
Receiver	PIN Diode
Wavelength	1300nm, 1550nm Single Mode
Fiber Optic Connectors	ST or FC
Loss Budget (1300/1550nm)	Single Mode LASER: 25dB Single Mode Hi-Power LASER: 32dB
Optical - Dual Fiber Side
Transmitter	LED/ELED
Receiver	PIN Diode
Wavelength	850/1300nm Multimode 1300nm Single Mode
Fiber Optic Connectors	ST or FC
Loss Budget (850/1300nm)	Multimode LED: 16dB Single Mode ELED: 16dB
System
Bit Error Rate	1 in 10¹⁰ or better

Visual Indicators
System	PWR A, PWR B, VccA, VccB
Optical Signal Status	MM RX, MM TX, SM RX, SM TX
Alarm
Dry Contact	Normal Open
Power
Standard	12VDC @ 700mA (max)
Optional	24VDC, -48VDC, or 115/230VAC (with external power cube)
Temperature
Operating	-10° to 50°C
Hi-Temp (optional)	-20° to 70°C
Storage	-40° to 90°C
Humidity	95% non-condensing
Physical (Standalone/Wallmount Unit)
Height	(3.53 cm) 1.4"
Width	(18.14 cm) 7.1"
Depth	(16.57 cm) 6.5"
Weight	(1.12 kg) 3.2 lbs.

Fiber Optic Mode Converter/Repeater With WDM

Applications

Fiber Optic Mode Converter/Repeater
With WDM